Reference materials

HYDROPAPA

+380445015929

+380675072240

+380674650171

+380955382171

+380636499813

Email:   hydropapa@ukr.net

 

PRESSURE RUBBER HOSES WITH TEXTILE REINFORCEMENT GOST-10362-76.

 

   This standard applies to pressure rubber hoses with textile reinforcement, used as flexible pipelines for supplying air, inert gases and liquids under pressure, operable in areas with a temperate and tropical climate at temperatures from minus 50 °Ñ up to plus 90 °Ñ, in regions with a cold climate at temperatures from minus 60 °Ñ to plus 90 °Ñ.

   This standard does not apply to a hose for gas welding and cutting of metals, a power hydraulic system of combine harvesters, food industry and diving equipment.

 

 MAIN PARAMETERS AND DIMENSIONS

(This table shows the dimensions and parameters of the hoses most used)

 

Inner

diameter (mm)

Working pressure, MPa

0,63

1,0

1,6

Outer diameter, mm

Weight 1m, kg (for reference)

Outer diameter, mm

Weight 1m, kg (for reference)

Outer diameter, mm

Weight 1m, kg (for reference)

6,0

-

-

-

-

14,0

0,16

8,0

-

-

15,5

0,17

16,5

0,21

10,0

17,5

0,20

17,5

0,2

18,5

0,24

12,0

20,0

0,25

20,0

0,25

20,0

0,25

14,0

22,0

0,28

22,0

0,28

23,0

0,32

16,0

24,0

0,32

24,5

0,34

25,0

0,36

18,0

26,0

0,35

26,5

0,37

27,0

0,40

20,0

28,5

0,41

28,5

0,41

29,0

0,43

25,0

34,0

0,49

34,0

0,52

35,0

0,59

32,0

41,5

0,69

42,5

0,77

43,0

0,81

38,0

47,5

0,80

48,5

0,89

49,0

0,94

40,0

49,5

0,84

50,5

0,93

51,5

0,96

50,0

60,0

1,08

61,5

1,32

51,5

1,65

63,0

74,0

1,48

74,0

1,48

76,5

1,88

80,0

93,0

2,21

92,0

1,67

94,0

2,36

100,0

113,0

2,72

113

2,72

117,5

3,80

 

HOSES must be operable in working environments at a temperature range:

 

Working environments

Working environment temperature, °Ñ

Aviation gasoline according to GOST 1012 and automobile gasoline according to GOST 2084

from - 50 to + 70

Jet fuels according to GOST 10227 and diesel fuels according to GOST 305

from - 50 to + 70

Petroleum based oils

up to +100

Liquid lubricants

from - 50 to + 100

Lubricant grease in accordance with GOST 1033

Air

from - 50 to + 60

Gases are neutral (inert)

Water

up to + 100, short-term up to + 120

Low -temperature cooling liquid according to GOST 28084

from - 60 to + 120

Weak solutions of inorganic acids, alkalis (up to 20% concentration), except for nitric acid

from - 50 to + 50

 

The minimum bending radius of the hose during operation must correspond to  the standards:

 

Inner diameter, mm

Minimum bend radius

up to 25

8 inner diameters

from 25 to 50

10 inner diameters

from 50 to 63

15 inner diameters

from 63 to 100

20 inner diameters

 The change in the outer diameter of the hose at the minimum bending radius should not be more than 10% of the actual diameter of the hose.

 

  GAMMA-percentage the resource of the hose, subject to the requirements of this standard, should be at a normal resource:

20 thousand km - for vehicle components and assemblies

5000 engine hours - for units and assemblies of tractors up to 01.01.92 ã.

Since 01/01/92, the resource of hoses for units and assemblies of tractors with γ = 0,9 – 8000 engine hours.

 

  In order to ensure tightness and operability of the hose, when tightening with clamps, the wall deformation is taken within 15% - 30%, when embedded in couplings – 25% - 45%.

 It is allowed to grind the outer rubber layer at the ends of the sleeves at a length of 25 – 30 mm, the entire stripped part of the hose must be clamped by the sleeve.

 

  It is NOT ALLOWED to reinforce the sleeve after it has been at a temperature below 0°Ñ without preliminary exposure at a temperature of 15°C to 25°C for 24 hours.


UP